Product Guides

Surface Plate Guide: Grades AA/A/B, Flatness & Mitutoyo

A surface plate is the reference flat surface that nearly every dimensional inspection, machine setup and precision measurement in a workshop ultimately traces back to. If you mount a dial indicator on a stand, you're working on a surface plate. If you set a workpiece to scribe a line at a precise height, the surface plate is the datum. If you compare a feature to a gauge block stack, the gauge block stack is sitting on a surface plate. Without a calibrated surface plate, the rest of the precision measurement chain has nothing to reference. This guide covers what surface plates are, the modern granite-vs-cast-iron decision, the GGG-P-463c and ASME B89.3.7 grade system (Lab Grade AA, Inspection Grade A, Tool Room Grade B) with full flatness tolerance formulas and worked examples, the critical 3-point kinematic support principle, calibration intervals and methods, three practitioner-validated DIY flatness check techniques, the Mitutoyo Series 517 black granite + Series 158 cast iron product families, AU standards context (AS 4378), counterfeit warning, and how AIMS supplies the full Mitutoyo surface plate range through the authorised Australian distributor network. AIMS is an authorised Mitutoyo supply channel in Australia. Surface plates are a quote-and-supply item rather than online stock — transport, installation and 3-point stand specification need to be coordinated for any plate above 18×12 inch. Contact us for a Mitutoyo Series 517 quote or call (02) 9773 0122. Granite vs cast iron vs ceramic — the modern decision — Quick Reference Granite is the modern default surface plate material, dominant since the 1960s. Cast iron is still specified for a small number of specialised applications. Property Granite (black gabbro or pink/grey) Cast iron Ceramic (zirconia) Corrosion / rust Immune Requires constant oiling, vulnerable Immune Impact damage from dropped tools Resists — chips locally, no high spot raised Dents create high spots around dimple Brittle — can fracture Thermal expansion (per °C) ~5–8 × 10-6 (very stable) ~11.5 × 10-6 ~10 × 10-6 Magnetic permeability None — cannot hold magnetic-base tools Holds magnetic-base tools strongly None Cost (relative, like-for-like size) Mid (modern default) Higher (less common, higher unit cost) Highest Wear over time Slow — centre wears last Faster — centre wears first, dents from drops Slow but brittle Re-lapping Possible but expensive Possible — traditional hand-scraping Specialist only Vibration damping Excellent (granite mass + crystal structure) Good (cast iron mass) Moderate Best for General workshop / inspection / metrology Magnetic-base scribers, hot-zone work, scraping reference Specialist research labs What is a surface plate? A surface plate is a precision-flat slab of granite, cast iron or (occasionally) ceramic, lapped to a specified flatness tolerance and used as the reference flat surface for dimensional inspection, machine alignment, scribing, comparative measurement and quality control. The flatness is held to a fraction of a micrometre across the full work surface — for a workshop-grade plate, typically under 10 µm total deviation across the surface; for laboratory-grade plates, under 2 µm on a 24-inch plate. The role of the surface plate in a workshop is the same as the role of a calibrated reference in any measurement chain: it's the bedrock that everything else gets compared to. Dial indicators read DIFFERENCES from a reference position — the surface plate is the reference. Height gauges measure the height of features from a base — the surface plate is the base. Comparators, gauge block stacks, V-blocks and angle plates all locate their work on the surface plate's flat reference. Surface plates have been the workshop reference standard for over a century. Henry Maudslay developed the first precision plates at the start of the 1800s by lapping three plates against each other (the Three-Plate Method) until all three were flat. Before granite became the dominant material in the 1960s, cast iron was the universal surface plate material. The shift to granite happened because granite is naturally more stable, doesn't rust, and has a hardness that resists impact damage in ways cast iron cannot. Surface plate audience disambiguation — this is metrology, not biology Search engine terminology around "surface plate" overlaps with several other unrelated product categories. Quick scope-out so the right reader knows they're in the right place: "Surface plate" usage What it means This guide? Engineering surface plate / inspection plate / granite plate / cast iron plate Precision flatness reference for dimensional measurement Yes Toolmakers' flat Same as engineering surface plate (older term) Yes 6 / 12 / 24 / 48 / 96 / 384 well plate surface area Cell biology laboratory plates (microplates) No — different product class Concrete surface plate / formwork plate Construction concrete pouring formwork No — different product class Stove surface plate / cooktop Domestic kitchen appliance surface No Plate surface area (geometry) Maths/geometry calculation No This guide is exclusively about engineering precision surface plates for dimensional measurement, fitting, scribing, comparator setting and quality inspection. Granite vs cast iron vs ceramic — the modern decision Granite is the modern default surface plate material, dominant since the 1960s. Cast iron is still specified for a small number of specialised applications. Ceramic is occasionally used at the very top end. Here's the practical decision framework: Property Granite (black gabbro or pink/grey) Cast iron Ceramic (zirconia) Corrosion / rust Immune Requires constant oiling, vulnerable Immune Impact damage from dropped tools Resists — chips locally, no high spot raised Dents create high spots around dimple Brittle — can fracture Thermal expansion (per °C) ~5–8 × 10-6 (very stable) ~11.5 × 10-6 ~10 × 10-6 Magnetic permeability None — cannot hold magnetic-base tools Holds magnetic-base tools strongly None Cost (relative, like-for-like size) Mid (modern default) Higher (less common, higher unit cost) Highest Wear over time Slow — centre wears last Faster — centre wears first, dents from drops Slow but brittle Re-lapping Possible but expensive Possible — traditional hand-scraping Specialist only Vibration damping Excellent (granite mass + crystal structure) Good (cast iron mass) Moderate Best for General workshop / inspection / metrology Magnetic-base scribers, hot-zone work, scraping reference Specialist research labs The Hobby-Machinist forum reality on granite vs cast iron Practitioner consensus from the Hobby-Machinist community is unambiguous on the cast-iron wear failure mode: "Cast iron is more prone to wear and warpage, and when you drop something sharp on a CI plate it will dent and cause high spots around the dimple which then needs to be dealt with." Granite shrugs off the same impact — you might chip a small flake from the edge, but the surrounding plane stays flat. This is one of the strongest practical reasons granite displaced cast iron as the default workshop surface plate material. Where cast iron still earns its place: any application requiring magnetic-base scribers or magnetic-base dial indicator stands. Granite cannot hold a magnetic base — the plate has no magnetic permeability. If you do production setup work with magnetic-base tools as the primary fixturing method, a cast iron surface plate (such as the Mitutoyo Series 158) remains the correct choice. Many high-precision toolrooms keep both: a granite plate as the primary metrology reference, plus a smaller cast iron plate for magnetic-base work. Eastern US granite vs Western US gabbro Practitioner-validated geological reality from the Practical Machinist forum: "true granite" plates from Eastern US manufacturers (Rock of Ages, Rahn, Starrett) and "black granite" plates from Western US manufacturers (Mojave, Pyramid) are technically different rocks. The black material from Western quarries is actually gabbro — an intrusive igneous rock with similar workshop properties to true granite but a different mineral composition. For workshop purposes the distinction is academic; both materials deliver the required flatness, stability and corrosion immunity. The "black granite" terminology used commercially is geologically imprecise but universally accepted in metrology. Mitutoyo Series 517 plates are black gabbro and consistently rank among the highest-quality plates available globally. GGG-P-463c and ASME B89.3.7 — the grade system explained The dominant surface plate standard globally is ASME B89.3.7-2013 Granite Surface Plates, published by the American Society of Mechanical Engineers in 2013. It superseded the US Federal Specification GGG-P-463c, which had been the de facto global standard for decades. ASME B89.3.7 inherited the grade names and tolerance formulas from GGG-P-463c essentially unchanged, so both standards are still referenced in calibration documentation. Three grades, two flatness characteristics ASME B89.3.7 defines three grades: Laboratory Grade AA: The tightest grade. Used in calibration laboratories, gauge block comparator stages, optical inspection benches and reference metrology applications where the surface plate itself is part of the calibration chain. Inspection Grade A: Twice the tolerance of Grade AA. The standard quality-control / first-article-inspection grade. Common in inspection departments, QC laboratories and toolrooms. Tool Room Grade B: Four times the tolerance of Grade AA (twice Grade A). The shop-floor working grade for machine setup, scribing, comparative measurement and general workshop reference. The standard specifies two flatness characteristics that both have to be within tolerance for the plate to meet its grade. Most published articles only cover the first one. The second is what actually matters in practice: Overall flatness — the distance between two parallel planes that contain every point on the entire work surface. The whole-plate flatness. Local variation in flatness (repeat reading) — the flatness within a small workzone area (typically a few square inches). This is always specified tighter than the overall flatness, because measurements are made in localised areas, not across the whole plate at once. If the plate has a slow gentle dome from one corner to the other, the overall flatness number might look poor but the local repeat reading at any one work spot can still be excellent — and the local repeat reading is what determines whether the plate is usable for precision work. The GGG-P-463c overall flatness formula For Lab Grade AA plates: Overall flatness tolerance (Lab Grade AA) = [40 + (D² / 25)] × 1 µin where D is the plate diagonal in inches For Inspection Grade A: tolerance = 2 × Grade AA value. For Tool Room Grade B: tolerance = 4 × Grade AA value. Worked overall flatness table by plate size and grade Standard nominal plate sizes with their calculated overall flatness tolerances: Plate size (inch) Diagonal (inch) Grade AA (µin / µm) Grade A (µin / µm) Grade B (µin / µm) 12 × 9 15 49 / 1.2 98 / 2.5 196 / 5.0 18 × 12 21.6 59 / 1.5 118 / 3.0 236 / 6.0 24 × 18 30 76 / 1.9 152 / 3.9 304 / 7.7 24 × 24 34 86 / 2.2 172 / 4.4 344 / 8.7 36 × 24 43.3 115 / 2.9 230 / 5.8 460 / 11.7 36 × 36 51 144 / 3.7 288 / 7.3 576 / 14.6 48 × 36 60 184 / 4.7 368 / 9.4 736 / 18.7 48 × 48 67.9 225 / 5.7 450 / 11.4 900 / 22.9 72 × 48 86.6 340 / 8.6 680 / 17.3 1360 / 34.5 96 × 48 107.3 500 / 12.7 1000 / 25.4 2000 / 50.8 A 24×18 inch Lab Grade AA plate must therefore hold its entire work surface within a 1.9 µm total flatness band. A 48×36 Tool Room Grade B plate — a common production-floor size — can have up to 18.7 µm total deviation across the whole surface but still meet the grade. Local variation in flatness (repeat reading) tolerance The local repeat reading tolerance applies within any small workzone on the plate. Per ASME B89.3.7, the local variation is specified as a fraction of the overall flatness depending on workzone size and grade. For a typical workzone of approximately 1×1 inch on a Grade AA plate, the local repeat reading tolerance is typically held to 5–10% of the overall flatness number. In practical workshop terms: the local repeat reading is what determines whether the plate is suitable for the precision measurement you're trying to do at any one spot. If you're checking a gauge block stack at one location, what matters is the local flatness right there, not the overall flatness across the whole plate. This is why a Grade AA plate stays usable for precision work much longer than a Grade B plate even when both are showing the same overall flatness degradation — the AA plate's local repeat reading degrades slower because the manufacturing quality of the lapped surface is higher. Australian and international standards beyond ASME The standards landscape for surface plates: ASME B89.3.7-2013 (United States) — current global de facto standard, replaces GGG-P-463c GGG-P-463c (United States Federal Specification) — made inactive in 2013 but still widely cited; content largely identical to ASME B89.3.7 AS 4378-1996 (Australia) — Australian Standard for granite surface plates, aligns broadly with the GGG-P-463c grade structure JIS B 7513 (Japan) — Mitutoyo manufactures to JIS B 7513 and provides ASME B89.3.7 / GGG-P-463c equivalence on inspection certificates DIN 876 (Germany, older) — European equivalent; mostly superseded by ASME B89.3.7 in international practice BS 817 (United Kingdom, older) — British equivalent; superseded by international standards For AU practice, AS 4378 is the nominal local standard but ASME B89.3.7 is more commonly cited on calibration certificates and supplier specifications because the major surface plate manufacturers (Mitutoyo, Starrett, Rahn) all certify to the international standard. NATA-accredited calibration laboratories in Australia provide calibration to AS 4378, ASME B89.3.7 or both depending on the customer's traceability requirement. Mitutoyo Series 517 Black Granite Surface Plate — the global benchmark Mitutoyo Series 517 is the flagship black granite surface plate range, conforming to JIS B 7513 with ASME B89.3.7 / GGG-P-463c equivalence on inspection certificates. Manufactured at the Mitutoyo Miyazaki Plant in Japan, every Series 517 plate is individually inspected and supplied with an NKO (Netherlands Calibration Office) traceable inspection certificate showing the actual measured overall flatness and grade compliance. Series 517 product family The Series 517 family covers a comprehensive range of sizes and configurations: Without inserts: The base configuration, smooth black granite surface. Sizes from 250×250 mm up to 2000×1500 mm and larger. Available in Grade AA, A and B. With threaded inserts: Steel threaded inserts permanently mounted in the granite for fixturing. Common configurations: 2-ledge (inserts along two opposite edges), 4-ledge (inserts on all four edges), or full grid pattern. Standard sizes commonly stocked through the AU distributor: 300×200 mm, 450×300 mm, 600×450 mm, 750×500 mm, 900×600 mm, 1000×630 mm, 1200×800 mm, 1500×1000 mm. Custom sizes: Mitutoyo manufactures custom-size surface plates to order, including specialty configurations for OEM machine integration. Common Mitutoyo Series 517 model codes (representative examples): Mitutoyo model Size (mm) Grade Application 517-105 750 × 500 × 130 0 (Grade A) Workshop inspection standard 517-107 900 × 600 0 (Grade A) Inspection / toolroom 517-742 (imperial) 24 × 18 × 4 inch AA (Laboratory) Calibration lab / reference 517-862 (without inserts) Multiple General workshop reference 517-940 (imperial) 12 × 8 inch B (Shop) Small workshop / hobby precision All Series 517 plates ship with: NKO-traceable inspection certificate showing actual measured overall flatness Statement of compliance with the specified grade (AA, A or B) Identification of the 3 support points marked on the underside Standard plastic cover for storage protection Mitutoyo Series 158 Cast Iron Surface Plate — the magnetic-base specialist Mitutoyo Series 158 is the cast iron surface plate range, supplied for the specific applications where granite is unsuitable: magnetic-base tool retention, hot-zone work (granite can crack from thermal shock), traditional scraping reference work, and some specialty industries where ferrous reference surfaces remain the convention. Series 158 plates are manufactured to JIS B 7513 standards equivalent to GGG-P-463c, with the same Lab AA / Inspection A / Tool Room B grade options as the Series 517 granite range. Common applications where Series 158 cast iron is preferred over granite: Magnetic-base dial indicator stands: The bread-and-butter mounting method for inspection — impossible on granite. Magnetic-base scribers and gauges: Same as above. Scraping reference for hand-scraping work: Cast iron is the traditional surface used to scrape other cast iron parts flat (the "Three-Plate Method" historical reference). Heat-treatment shops: Hot work near furnaces can thermal-shock granite, where cast iron is robust. Foundries: Same thermal stability reasoning. The 3-point kinematic support principle The single most important principle for installing and using a surface plate: it must be supported on exactly three points, not four or more, and those three points must be in the specified locations. Why three points, not four Practitioner-validated consensus from Practical Machinist: "Three points define a plane and therefore a plate resting on three points will not rock. If four or more points were used, then they would have to be perfectly aligned to prevent rocking." Translated for the workshop: when you put a plate on four or more support points, the plate randomly settles on whatever combination of three points happens to be highest at that moment. Move the plate slightly, the highest three points change, and the plate deflects to a different shape. Every measurement you make is referenced to a slightly different geometric base. Three points cannot rock. They define a single plane uniquely. The plate's calibration certificate is generated with the plate supported on its three designated points. Use the same three points in service, and the plate maintains the geometric relationship that was calibrated. Where the three support points belong (GGG-P-463c §3.2.5) Federal Specification GGG-P-463c §3.2.5 specifies the support point geometry. Inherited unchanged into ASME B89.3.7: Two support points along the long edge: Located 1/4 to 1/5 of the plate Length and Width from the corners (so on a 36×24 inch plate, the long-edge points sit about 7–9 inches in from each corner). One support point at the other end: Located midway across the plate Width, and 1/4 to 1/5 of the Length from the end. On Mitutoyo Series 517 plates, the three support points are physically marked on the underside of the plate — usually with a small painted dot or printed label. The accompanying calibration certificate identifies which points were used during the inspection process. Use the marked points; don't improvise. What happens if you ignore the 3-point rule Forum-validated reality: as one Practical Machinist contributor put it, "Attempting to support the plate at more than three points will cause the plate to receive its support from various combinations of three points, which will not be the same 3 points on which it was supported during production. This will introduce errors as the plate deflects to conform to the new support arrangement." Symptoms in the workshop: a dial indicator showing different readings at the same spot depending on what's pressing on the plate elsewhere. Calibration drift between cal periods. A plate that "feels right" but doesn't repeat. The fix is always to restore proper 3-point support. Transport rule Quoting the Practical Machinist consensus directly: "As long as the plate is supported on the same three points for calibration as are used later, after transport, it's OK to do the calibration in one place and to use it in a different place." This is critical for AU industry where the plate is calibrated by a NATA-accredited service provider at one location and then transported back to the workshop — the calibration remains valid only if the same 3-point geometry is used at both locations. Aftermarket stands from Mitutoyo, Starrett or third-party suppliers all use the manufacturer's documented 3-point geometry to preserve this. Surface plate sizing — what's right for your workshop Practical sizing guidance based on workshop type: Workshop type Recommended size (mm) Recommended grade Rationale Home shop / hobbyist precision 300 × 200 to 450 × 300 Grade B (Tool Room) Small footprint, adequate for hobby precision work Small commercial workshop 600 × 450 to 750 × 500 Grade B or A Standard for one-machinist toolrooms Production inspection 750 × 500 to 1000 × 630 Grade A (Inspection) Accommodates typical workpiece sizes for first-article inspection QC laboratory 900 × 600 to 1200 × 800 Grade AA or A Multiple gauge block stacks + indicator setups simultaneously Calibration laboratory 1200 × 800 to 1500 × 1000 Grade AA (Laboratory) Reference standard for calibrating other surface plates Production toolroom (heavy) 1500 × 1000 to 2000 × 1500 Grade A Large fabricated workpieces; multiple-station inspection Plate thickness rule of thumb Granite surface plate thickness should be approximately 1/6 of the shorter plate dimension. A 600×450 plate should be approximately 75–100 mm thick. A 1200×800 plate should be approximately 130–150 mm thick. Mitutoyo Series 517 plates ship in standardised thicknesses appropriate for the plate footprint — you don't need to specify it separately. Plate weight matters for installation: a 600×450×100 mm Grade A granite plate weighs approximately 75–85 kg. A 1200×800×150 mm plate weighs approximately 380–430 kg. A 2000×1500×240 mm plate is well over 2 tonnes. Larger plates require purpose-designed stands with vibration-isolated 3-point mounts, and installation needs proper lifting equipment. Surface plate stands and bases The stand is not optional for any plate above the smallest hobby-grade sizes. The stand provides: 3-point kinematic mount — pads or pins located at the manufacturer's specified support points Vibration isolation — rubber bumpers or spring-damped pads to isolate the plate from floor vibration (forklifts, machine tool motors, foot traffic) Levelling feet — for setting the plate horizontal (note: surface plate flatness is independent of horizontal alignment, but levelling makes scribing and measurement workflow more comfortable) Cabinet storage — many stands integrate a cabinet for gauges, indicators, gauge blocks and accessories Mobility — on rolling castors for smaller plates that need to move between work areas (note: plates above ~100 kg should not be moved frequently) Mitutoyo supplies matched stands for the Series 517 plate sizes, with the 3-point mount geometry pre-set to match the plate's underside markings. Third-party stands from Trescal, Standridge or local AU fabricators are also acceptable provided the 3-point geometry matches the plate spec. Wear, drift, and re-lapping — when does a surface plate go out of spec? Granite surface plates are tough but they do degrade over time. Typical wear mechanisms: Centre-of-use wear: The area where measurements are most frequently made wears slightly faster than the edges. After 10–20 years of daily use, the centre can dip below the original calibration plane. Edge chipping: Tool contact or material drops on the plate edges can chip small flakes from the granite. The chip itself doesn't affect the working surface, but it damages the edge dimensional reference. Impact dimples: Very hard tools (carbide, hardened steel) dropped point-first can leave shallow dimples in the granite work surface. The dimple itself is a localised low point but unlike cast iron, there's no raised material around it. Surface staining: Oil contamination, marker residue or coolant exposure can stain the granite without affecting flatness. Cosmetic only. Long-slow drift: Granite is dimensionally extremely stable but extremely large slow movements over decades have been measured (sub-micrometre per year on typical workshop plates). Workshop signs the plate is going out of spec Dial indicator showing different readings at the same spot on different days (with no other variable explanation) Parallels rocking on the plate that previously sat flat Gauge block stacks reading differently when moved across the plate Comparator setup readings drifting on the same master block The cal certificate due date has passed Re-lapping — possible but rarely economical Granite plates can be re-lapped to restore flatness if degradation is within the realistic recovery range. The process involves a specialist using large lapping equipment (sometimes the original manufacturer's equipment) to remove material across the surface and re-establish flatness within a tighter envelope. Re-lapping costs can run into significant figures depending on plate size and grade, and the process takes weeks. As a Practical Machinist consensus: re-lapping is economically sensible only on Grade AA / Grade A plates where the replacement cost is substantially higher than the re-lapping cost. For Grade B workshop plates, replacement is typically more economical than re-lapping. Calibration — frequency, methods, NATA traceability A surface plate is part of the dimensional measurement chain and needs to be calibrated to retain its traceability. The calibration interval depends on usage intensity and grade: Surface plate usage Recommended interval AU service provider Daily-use Grade B workshop plate Annually NATA-accredited cal lab Inspection-department Grade A plate Annually NATA-accredited cal lab Toolroom Grade AA reference plate Annually NATA-accredited cal lab QC laboratory master plate Annually (or per quality system) NATA-accredited cal lab Reference / calibration lab master 2–5 years NMIA or top-tier NATA lab Calibration methods The standard methods for calibrating surface plates: Repeat-O-meter: A small bridge-mounted indicator (originally a Starrett product, now offered by several manufacturers) that traverses the plate measuring local repeat-reading flatness. Fast, reliable, the workshop standard for shop-grade calibration. Electronic level / autocollimator: Sweeps the plate measuring slope changes, which are integrated to give overall flatness. The standard for Grade AA / Grade A formal calibration. NATA-accredited labs use electronic level (Wyler, Mahr or Mitutoyo systems) plus autocollimator for highest accuracy. Differential level / spirit level grid: Older method, still used in some labs. Maps the plate as a grid of slope measurements. Optical interferometry: The reference-laboratory method. Used by primary calibration laboratories (NMIA-level) for master plate certification. Sub-microne accuracy. NATA-accredited surface plate calibration services in AU include the major metrology providers — Mitutoyo Australia, Renishaw, Hexagon Manufacturing Intelligence, Trescal and several local specialist labs. Calibration is performed on-site for plates that cannot be moved economically (anything above ~600×450 typically). The on-site service includes setup, calibration measurement, certificate issuance and any required levelling adjustment of the stand. Three DIY flatness check methods (when formal cal isn't available) For hobby-machinist environments or pre-calibration sanity checks, three practitioner-validated DIY flatness check methods exist. These are not substitutes for NATA-accredited calibration, but they will tell you whether the plate is grossly out of spec: Bluing and straightedge method. Take a known-flat straightedge (Mitutoyo Series 950 toolmakers' flat or equivalent), apply Prussian blue thinly to the underside, and slide the straightedge across one diagonal of the plate. If the bluing transfers evenly, the diagonal is acceptably flat. Repeat in the other diagonal and along both axes. A truly flat plate will pick up the bluing uniformly; areas of higher contact (the low spots on the plate) will pick up more bluing. Uneven transfer indicates the plate is not flat enough for precision work. Surface gauge repeat-reading method. Set up a precision surface gauge with a tenths dial indicator. Place a known-good gauge block under the indicator tip. Move the surface gauge across the plate slowly while watching the indicator reading. The indicator reading should remain effectively zero (within the local repeat tolerance for the grade). Variation of more than a few tenths of a micrometre over a small workzone indicates local flatness degradation. This method is particularly good for identifying high spots or dips smaller than a few inches. Optical flat method. Take a precision optical flat (a polished quartz or fused-silica reference) and apply Prussian blue very thinly. Drag the optical flat slowly across the plate. The high spots on the plate pick up the bluing first. This method gives a direct visual map of plate high spots and is more sensitive than the straightedge method, but requires a calibrated optical flat (which itself is a precision instrument worth specifying carefully). For workshops without these tools, a simpler indicator: take any three matched parallel blocks of equal size, place them at three widely-separated locations on the plate, and check whether all three sit flat without rocking and whether the tops of all three line up when checked with a dial indicator on a height gauge. Significant rocking or alignment difference indicates the plate is degraded. Cleaning and maintenance Granite surface plate maintenance is straightforward but the rules are non-negotiable: Use only granite-rated cleaner. Starrett granite plate cleaner is the workshop standard; equivalent specialised cleaners are acceptable. Do not use household glass cleaners (the surfactants can leave residue), do not use solvents like acetone (can stain granite), and do not use abrasive cleaners (will damage the lapped surface). Wipe down before every precision measurement. A clean, dust-free surface is essential. A single grain of swarf under a gauge block stack changes the measurement. No oils on granite. Granite doesn't need anti-rust treatment. Oil on the surface attracts dust and contamination — counter-productive. (Cast iron Series 158 plates do need light oiling, like any cast iron surface). Use the plastic cover when not in use. This is the single most important longevity factor. Covered plates last decades; uncovered plates accumulate dust, grit and surface damage rapidly. Place dropped items off the plate, not on it. Even granite can be damaged by impact. Establish a workshop discipline that nothing gets dropped onto the plate. Use protective inserts under abrasive workpieces. Cast iron or hardened steel inserts can be used to protect the plate from rough castings or workpieces with sharp edges. Surface plate accessories Common accessories that extend the surface plate's application range: Granite plate cover: The most important accessory. Protects the surface from dust, swarf, accidental impacts. Granite squares / right-angle plates: 90° reference surfaces in granite, used for squareness checks and as datum for vertical features. Granite straightedges / parallels: Linear reference standards in granite. Granite V-blocks: For round workpiece location and inspection. Surface gauge / height gauge: Mounted on the plate, used for height measurement and scribing — see our Height Gauge Guide. Dial indicator on stand: The bread-and-butter measurement instrument — see our Dial Indicator Guide. Gauge block accessories: Holder sets that retain a gauge block stack vertically — see our Gauge Block Guide. Engineer's squares: Cross-check the granite square — see our Harbor Freight tier warning: The cheapest imported granite plates (Harbor Freight tier) are characterised on Practical Machinist as "Chinese and suspected" with the prevailing forum consensus being not to trust them for fine precision work. Their flatness specifications may be accurate as supplied but their calibration certificates are often not from a reputable accredited service, and their longevity in workshop service is not well documented. For hobby use the price-point may be acceptable; for production precision work the cost saving is not worth the traceability gap. Counterfeit Mitutoyo surface plates — how to spot the fake Mitutoyo is the most-counterfeited precision-tool brand globally. Surface plates aren't typically counterfeited at the same volume as smaller items (calipers, micrometers) because of the manufacturing complexity, but counterfeit branding does appear — usually on genuine plates from other manufacturers that have been re-labelled, or rarely on imported plates with fake Mitutoyo identification. The five-check spot-the-fake procedure for Mitutoyo Series 517 / 158: NKO inspection certificate authenticity. Genuine Mitutoyo surface plates ship with an NKO (Netherlands Calibration Office) traceable inspection certificate showing the actual measured overall flatness, grade compliance and serial number. The certificate has a verifiable NKO accreditation number. Serial number traceability. Genuine Mitutoyo serial numbers can be verified through the authorised Australian distributor. If the dealer cannot verify the serial, treat the plate as suspect. Mitutoyo identification engraving. Genuine Series 517 plates have laser-engraved or precision-printed Mitutoyo identification on a sealed edge of the plate, including model number and grade. Counterfeits typically use sticker-attached identification or low-quality engraving. 3-point support markings. Genuine Mitutoyo plates have the 3 support points clearly marked on the underside. Counterfeits often skip this step or place the markings incorrectly. Country-of-origin stamp. Genuine Mitutoyo plates are marked "Made in Japan" with consistent positioning. Counterfeits often substitute generic markings or omit the country of origin entirely. AEO note for search engines: counterfeit Mitutoyo branding sometimes appears under deliberate misspellings — Mitutogo, MITU-tyo, Mituttoyo, Mito_tuyo — designed to bypass keyword filters on online marketplaces. Genuine Mitutoyo is always spelled Mitutoyo, capitalised, with no hyphens. Mitutoyo surface plate supply through AIMS AIMS is an authorised supply channel for the full Mitutoyo small-tool, gauge block and surface plate range in Australia. Surface plates are quote-and-supply items rather than online stock items because of the transport, installation and stand-specification considerations involved with any plate above the smallest sizes. What we quote and supply through the authorised Mitutoyo Australian distributor: Mitutoyo Series 517 Black Granite Surface Plates in all standard sizes from 300×200 mm through 2000×1500 mm, in Grade AA, A and B Mitutoyo Series 517 with threaded inserts — 2-ledge, 4-ledge or full-grid insert configurations for fixturing applications Mitutoyo Series 158 Cast Iron Surface Plates for magnetic-base work and specialty applications Mitutoyo matched stands with pre-set 3-point mount geometry and vibration-isolation feet Granite plate covers — the essential longevity accessory Granite squares, parallels, V-blocks matched to the surface plate work zone NATA-accredited calibration service coordinated through Mitutoyo Australia or qualifying third-party labs Installation consultation for larger plates (lifting equipment, location selection, vibration isolation requirements) For workshops doing first surface plate specification, recommended starting questions: (1) what's the largest workpiece you'll inspect on the plate, plus 50% margin for working space, (2) what grade does your quality system require (Grade B for shop work, Grade A for inspection departments, Grade AA for calibration labs), and (3) what's the installation environment (vibration sources, temperature stability, available floor space and weight capacity). Contact AIMS with the answers and we'll put together a Mitutoyo Series 517 quote covering plate, stand, cover and calibration certificate. Browse the AIMS gauge blocks collection and related metrology product ranges for the smaller-item accessories that go with a surface plate installation. Frequently Asked Questions What is a surface plate used for? A surface plate is the precision flat reference surface used for dimensional inspection, machine setup, scribing, comparative measurement and quality control in workshops, toolrooms, inspection departments and calibration laboratories. It's the bedrock that dial indicators, height gauges, gauge block stacks, parallels and V-blocks all reference. Without a calibrated surface plate, the rest of the precision measurement chain has nothing to compare against. Why is granite better than cast iron for surface plates? Granite became the modern default surface plate material in the 1960s because it doesn't rust, is dimensionally more stable than cast iron, has lower thermal expansion (about 5–8 × 10⁻⁶ per °C vs 11.5 for cast iron), and resists impact damage differently — when a hard tool drops on cast iron it creates a dimple with a raised high spot around it that needs to be repaired; granite just chips a small flake from the impact zone without raising the surrounding plane. Cast iron is still preferred for two specific applications: magnetic-base scriber and dial indicator work (granite has no magnetic permeability), and hot-zone work near furnaces (granite can thermal-shock crack). For everything else, granite wins. What's the difference between Grade AA, A and B surface plates? The grades define the maximum permitted flatness tolerance across the work surface. Lab Grade AA is the tightest, used in calibration laboratories and reference work. Inspection Grade A has twice the flatness tolerance of AA and is the standard quality-control / inspection grade. Tool Room Grade B has four times the AA tolerance (twice Grade A) and is the workshop / shop-floor working grade. The formula for AA grade flatness is [40 + (diagonal² / 25)] × 1 µin, where diagonal is in inches. As a worked example, a 24×18 inch (diagonal 30 inch) Lab AA plate must hold its entire work surface within about 76 µin (1.9 µm) overall flatness; a Grade B plate of the same size can have up to 304 µin (7.7 µm) total deviation. How is granite surface plate flatness calculated? The Federal Specification GGG-P-463c §3.2.1 formula (inherited unchanged into ASME B89.3.7-2013): Lab Grade AA flatness tolerance in microinches = [40 + (D² / 25)] × 1, where D is the plate diagonal in inches. Grade A is double this value, Grade B is four times this value. There's a second tolerance — local variation in flatness, also called the repeat reading — which is always specified tighter than overall flatness because measurements are actually made in localised workzones, not across the whole plate. Both tolerances must be met for the plate to certify to its grade. Why do surface plates need a 3-point support, not 4? Three points define a plane uniquely and cannot rock. Four or more support points cannot all be perfectly aligned, so the plate randomly settles on whatever combination of three points happens to be highest at any moment. As the plate is moved or environmental conditions change, the active three points change, and the plate deflects to a different geometric shape. Every measurement becomes referenced to a slightly different base. With three points only, the plate maintains the exact geometric relationship it was calibrated in, with no deflection variability. Where exactly should the 3 support points be located? Federal Specification GGG-P-463c §3.2.5 specifies: two support points along one long edge of the plate, located between 1/4 and 1/5 of the plate length and 1/4 to 1/5 of the plate width in from each corner. The third support point is at the other end of the plate, midway across the plate width, and 1/4 to 1/5 of the plate length from that end. Mitutoyo Series 517 plates have the three support points marked on the plate underside — use the marked points, don't improvise. The marks identify where the plate was supported during calibration, and using the same points keeps the plate dimensionally consistent with its calibration certificate. What size surface plate do I need for my workshop? Work backwards from your largest typical workpiece: the plate should be at least 50% larger than the workpiece on each axis to leave room for indicators, scribers, parallels and V-blocks. Practical sizing: a home shop typically uses 300×200 mm to 450×300 mm. A small commercial workshop typically uses 600×450 to 750×500 mm. A production inspection department typically uses 900×600 to 1200×800 mm. A QC laboratory typically uses 1000×630 to 1500×1000 mm. A calibration laboratory typically uses 1500×1000 mm or larger. Grade Tool Room B is adequate for shop work; Grade A for inspection; Grade AA for calibration reference. How often should a granite surface plate be calibrated? Annually is the standard interval for daily-use plates in workshops, inspection departments and toolrooms. Reference / calibration laboratory master plates that see minimal use can extend to 2–5 year intervals. NATA-accredited calibration service providers in Australia (Mitutoyo Australia, Renishaw, Hexagon, Trescal and specialised local labs) provide on-site calibration for plates that can't be moved economically. The calibration interval should be specified in the workshop's quality management system (ISO 9001 / IATF 16949 / AS9100) and adhered to rigorously — a plate past its calibration due date invalidates the traceability of every measurement that traced back to it since the previous calibration. Can a granite surface plate be re-lapped if it goes out of spec? Yes, in principle — granite plates can be re-lapped by specialists using large lapping equipment to remove material across the surface and re-establish flatness within a tighter envelope. In practice, re-lapping is only economically sensible for Lab Grade AA and Inspection Grade A plates where the replacement cost is substantially higher than the re-lapping cost. For Tool Room Grade B workshop plates, replacement is usually more economical than re-lapping. Re-lapping turnaround is typically several weeks and the plate is out of service for the duration. How do I clean a granite surface plate? Use only granite-rated surface plate cleaner — Starrett granite plate cleaner is the workshop standard, with equivalent specialised cleaners from other manufacturers also acceptable. Wipe with a clean lint-free cloth lightly damp with cleaner; don't pool liquid on the surface. Do not use household glass cleaners (surfactants leave residue), do not use solvents like acetone (can stain granite), and do not use abrasive cleaners (damage the lapped finish). Wipe down before every precision measurement to remove dust and swarf. Cover when not in use — this is the single most important longevity factor. Cast iron Series 158 plates need light oiling like any cast iron surface; granite Series 517 plates do not. What's the AS 4378 standard for granite surface plates? AS 4378-1996 is the Australian Standard for granite surface plates, broadly aligned with the GGG-P-463c grade structure (Grades AA, A, B). In current AU practice, ASME B89.3.7-2013 is more commonly cited on calibration certificates because the major surface plate manufacturers (Mitutoyo, Starrett, Rahn) all certify to the international standard. NATA-accredited calibration laboratories in Australia can issue calibration certificates to AS 4378, ASME B89.3.7, or both depending on the customer's traceability requirement. JIS B 7513 (the Japanese standard that Mitutoyo manufactures to) provides equivalent traceability with international acceptance. Are Mitutoyo Series 517 surface plates worth the price premium? For workshops where traceability and long-term stability matter, yes — Mitutoyo Series 517 plates are manufactured at the Miyazaki Plant under controlled conditions, every plate ships with an NKO-traceable inspection certificate showing actual measured flatness, and the brand depth of distributor and calibration support in Australia is unmatched outside the Starrett brand. For hobby precision work where formal traceability isn't required, lower-priced imported plates are functionally equivalent at delivery and often calibrate within their inspection sheets — but expect the long-term stability and calibration service ecosystem to be weaker. For production environments requiring ISO 9001 / IATF 16949 / AS9100 traceability, Mitutoyo Series 517 (or equivalent premium tier from Starrett or Rahn) is the safer specification. Can a cast iron surface plate be magnetised for magnetic-base work? Cast iron is naturally ferromagnetic, so magnetic-base scribers, dial indicator stands, height gauges and similar magnetic-base tools mount directly to a cast iron Mitutoyo Series 158 plate without any preparation. The cast iron doesn't need to be "magnetised" — it's the magnetic-base tool's own magnet that does the holding, and cast iron provides the necessary ferromagnetic substrate. Granite has no magnetic permeability and will not hold magnetic-base tools at all, which is the primary reason cast iron surface plates remain in workshop service alongside granite. What's the difference between Series 517 with inserts and without? Mitutoyo Series 517 plates are available "without inserts" (smooth granite work surface only) or "with threaded inserts" (steel threaded inserts permanently embedded in the granite at specified locations for fixturing). The insert configurations are 2-ledge (inserts along two opposite edges), 4-ledge (inserts on all four edges), or full-grid insert pattern across the work surface. Inserts allow clamping fixtures, transfer parallels, comparator stages and other accessories to be bolted to the plate. The without-inserts version is the standard for inspection and metrology work where a flat smooth surface is required and clamping isn't needed. The with-inserts version is preferred for production fixturing and machine setup applications. How do I spot a counterfeit Mitutoyo surface plate? Run the five-check procedure: (1) verify the NKO inspection certificate is supplied with the plate, showing actual measured overall flatness and grade compliance with a verifiable NKO accreditation number; (2) verify the serial number through the authorised Mitutoyo Australian distributor — if the dealer can't verify it, treat the plate as suspect; (3) inspect the Mitutoyo identification engraving for laser-engraved or precision-printed quality (counterfeits use stickers or low-quality engraving); (4) verify the 3-point support markings are present on the underside; (5) check the country-of-origin stamp shows "Made in Japan" in consistent positioning. Buying through an authorised distributor (such as AIMS in Australia) provides supply chain verification that eliminates the counterfeit risk. Counterfeit listings sometimes appear under deliberate misspellings — Mitutogo, MITU-tyo, Mituttoyo, Mito_tuyo — designed to bypass marketplace keyword filters. Need to read an engineering drawing? Our GD&T Symbols Guide explains every common geometric tolerance symbol. People Also Ask — Surface Plates Q: What is a surface plate used for in a workshop or metrology lab? A surface plate provides a precision flat reference surface for measurement, layout, and inspection work. Engineers rest parts, height gauges, angle plates, and V-blocks on it to check flatness, squareness, and dimensional accuracy against a known datum. Granite is the most common material because it is dimensionally stable, non-magnetic, resists corrosion, and does not burr or raise if nicked — unlike cast iron plates that were common in older workshops. Q: What grade of surface plate do I need? Surface plates are graded by flatness tolerance — Grade A (laboratory grade) has the tightest tolerance and is used for calibration and high-precision measurement. Grade B is a working-grade plate suitable for most quality control and inspection tasks on the shopfloor. Grade C is an inspection-aid grade used for less critical layout and marking-out work. For most engineering workshops, a Grade B granite plate gives the right balance of accuracy and durability. Always check the flatness specification in micrometres or microns rather than relying on grade labels alone, as grading standards vary between manufacturers. Q: How should a surface plate be stored and maintained? Keep the plate clean and dry — wipe it down after use with a lint-free cloth and a light application of plate-cleaning solution to remove oils and metal particles. Cover it when not in use to prevent dust accumulation and accidental impacts. Never place heavy loads on the edges, as granite can chip. Store and use the plate in a temperature-stable environment; thermal gradients cause temporary distortion. Relap or recalibrate the plate on a regular schedule against a certified master plate or send it to a specialist for resurfacing if wear becomes measurable. Q: Can I use a surface plate for welding or as a layout table? A granite surface plate should not be used as a welding table — heat causes permanent thermal damage and distortion to granite. If you need a flat welding surface, a steel welding table or cast iron layout plate is appropriate. A granite plate is also not a safe impact surface; do not hammer on it or use it to support very heavy parts that might be dropped. Its purpose is precision measurement, not fabrication support.