Sutton MG 21.50-23.75 mm Adjustable Hand Reamer - TCA
Available
The Sutton R109 is an adjustable hand reamer in TCA (Tungsten Chrome Alloy), with straight flutes, a bright finish (uncoated and polished) and a square end for turning by hand with a suitable wrench. It is a general-purpose reamer, and the point of an adjustable reamer is that one tool covers a range of hole sizes instead of a single fixed diameter.
There are 22 sizes, from MA8 (6.35 to 7.15 mm) up to MO (69.75 to 85.00 mm). The ranges run end to end with no gaps, so every hole diameter from 6.35 mm to 85.00 mm sits inside at least one reamer's range. Spares are listed for the larger sizes: replacement blade sets (R110) and adjusting nuts (R112) for MA to MO, and pilots (R111) for MA to ML. There are no separate blades, pilots or nuts listed for the smaller sizes (MA8 to MA2). Five sets (M1, M2P, M3, M6 and M8) bundle groups of sizes, and a pilot-only set (R111 MA1) is available.
Where this product is used
- Hand reaming of drilled or bored holes across a size range with a single tool.
- Toolroom, workshop and maintenance work where the finished size varies from job to job.
Choosing the right size
Find your hole diameter in the range columns. The table also shows which replacement parts are listed for each size.
| Size | Range (mm) | Range (inch) | Square drive Sq (mm) | R110 blade set | R111 pilot | R112 nut |
|---|---|---|---|---|---|---|
| MA8 | 6.35 to 7.15 | 1/4 to 9/32 | 2.8 | No | No | No |
| MA7 | 7.15 to 7.95 | 9/32 to 5/16 | 3.2 | No | No | No |
| MA6 | 7.95 to 8.70 | 5/16 to 11/32 | 4 | No | No | No |
| MA5 | 8.70 to 9.50 | 11/32 to 3/8 | 4 | No | No | No |
| MA4 | 9.50 to 10.25 | 3/8 to 13/32 | 4 | No | No | No |
| MA3 | 10.25 to 11.00 | 13/32 to 7/16 | 4.5 | No | No | No |
| MA2 | 11.00 to 12.00 | 7/16 to 15/32 | 5.5 | No | No | No |
| MA | 12.00 to 13.50 | 15/32 to 17/32 | 5.5 | Yes | Yes | Yes |
| MB | 13.50 to 15.00 | 17/32 to 19/32 | 6.5 | Yes | Yes | Yes |
| MC | 15.00 to 16.75 | 19/32 to 21/32 | 7 | Yes | Yes | Yes |
| MD | 16.75 to 18.25 | 21/32 to 23/32 | 8 | Yes | Yes | Yes |
| ME | 18.25 to 19.75 | 23/32 to 25/32 | 9 | Yes | Yes | Yes |
| MF | 19.75 to 21.50 | 25/32 to 27/32 | 10 | Yes | Yes | Yes |
| MG | 21.50 to 23.75 | 27/32 to 15/16 | 12 | Yes | Yes | Yes |
| MH | 23.75 to 27.00 | 15/16 to 1-1/16 | 13 | Yes | Yes | Yes |
| MI | 27.00 to 30.25 | 1-1/16 to 1-3/16 | 15 | Yes | Yes | Yes |
| MJ | 30.25 to 34.25 | 1-3/16 to 1-11/32 | 15 | Yes | Yes | Yes |
| MK | 34.25 to 38.00 | 1-11/32 to 1-1/2 | 17 | Yes | Yes | Yes |
| ML | 38.00 to 46.00 | 1-1/2 to 1-13/16 | 21 | Yes | Yes | Yes |
| MM | 46.00 to 56.00 | 1-13/16 to 2-7/32 | 26 | Yes | No | Yes |
| MN | 56.00 to 69.75 | 2-7/32 to 2-3/4 | 32 | Yes | No | Yes |
| MO | 69.75 to 85.00 | 2-3/4 to 3-11/32 | 38 | Yes | No | Yes |
Getting a clean hole by hand
- Take a light cut. A common hand-reaming allowance is 0.08 to 0.13 mm. Too little and the reamer burnishes instead of cutting; too much and it is hard to turn by hand.
- Lubricate generously. A lack of lubricant causes tool wear and a poor finish (fix: increase the supply). Straight cutting oil is the usual choice in reaming because the aim is finish rather than cooling.
- Start with a good hole. A badly drilled hole is listed against all four problems (breakage, wear, chatter and poor finish) and the fix is to replace the drill.
- Keep it aligned, rigid and steady. Misalignment causes breakage and wear (fix: align the holes) and lack of rigidity causes breakage and chatter (fix: improve rigidity). Entering the work too fast is listed against breakage and chatter, and the fix is a slower approach feed.
Key specifications
| Specification | Detail |
|---|---|
| Catalogue code | R109 |
| Type | Adjustable hand reamer |
| Material | TCA (Tungsten Chrome Alloy) |
| Finish | Bright (uncoated, polished) |
| Flute geometry | Straight |
| Use | By hand with a suitable wrench, general purpose |
| Sizes in this range | 22 sizes, MA8 to MO |
| Overall adjustment range | 6.35 mm to 85.00 mm (1/4 in to 3-11/32 in) |
| Designation | N |
Related reaming tools
Browse the adjustable hand reamer collection for the full range, or see the replacement parts: R110 replacement blade sets, R111 pilots and R112 adjusting nuts. Sets that bundle common sizes are listed under R109 adjustable reamer sets and reamer-only sets. For fixed-size hand reaming see the R100 hand reamers, and for tapers the R105 taper pin reamer.
Having reaming problems? Our Cutting Tool Troubleshooting Guide covers reamers alongside drills and taps.
Resources
Couldn't load pickup availability
Secure Checkout. We do not store credit card details
Sutton Tools R109 Adjustable Hand Reamer - Tungsten Chrome Alloy: 21.50 - 23.75
SKU: A0012347 | Model: R1092150
Reamer Range (mm) 21.50 - 23.75. Descriptions
Sutton R109 adjustable hand reamer in TCA (Tungsten Chrome Alloy), with straight flutes, for general-purpose hand reaming.
22 sizes from MA8 to MO covering 6.35 mm to 85.00 mm, with replacement blades, pilots and nuts for the larger sizes.