Buy Tool Holder Accessories Online in Australia
Tool Holder Accessory Selection — Quick Reference
Tool holder accessories = ARBORS + ADAPTERS + live centres + fly cutter holders + tapping-head hardware bridging different machine tapers, chuck systems and workholding setups. Toolroom, mill and lathe support gear.
| Tool Holder Accessory | Best For |
|---|---|
| Drill Chuck Arbor / Taper Adapter | Fitting a drill chuck (or a different taper) to your spindle or tailstock |
| Lathe Live Centre | Rotating tailstock support for turning between centres |
| Fly Cutter Holder | Single-point facing/fly-cutting on the mill |
| Annular Cutter Arbor (MT2/MT3 + Coolant Ring) | Adapting a Weldon-shank annular cutter to a Morse-taper spindle |
| Tapmatic Tapping-Head Hardware | Pull stud, quill clamp, stop arm, BT arbor — servicing a Tapmatic tapping head |
| Automatic Centre Punch | Fast, spring-loaded centre-marking without a hammer |
Critical: Match BOTH ends of an arbor or adapter exactly — the machine-side taper (Morse, R8, NT/ISO, BT, DIN) AND the tool-side taper or thread (Jacobs, DIN, Weldon) — a mismatched taper won't seat properly and causes runout. Brands: Maxigear, Llambrich, Shin-Yain, Sutton Tools, MAXBOR, Euroboor, Trax. Companion: drill chucks, tapping heads, magnetic drills, indexable turning tool holders.
Tool Holder Accessories for Australian Machine Shops and Toolrooms
Tool holder accessories cover the arbors, adapters, live centres and hardware that let one taper or chuck system work with another, and that keep tool-holding setups running. That includes arbors fitting a Jacobs-taper drill chuck to a Morse-taper tailstock, an R8 mill spindle, an NT/ISO taper or a BT taper; lathe live centres supporting work at the tailstock; fly cutter holders for single-point facing on the mill; arbors adapting Weldon-shank annular cutters to a Morse-taper spindle; and the pull studs, quill clamps, stop arms and mounting arbors that keep a Tapmatic self-reversing tapping head serviceable. AIMS Industrial supplies tool holder accessories for Australian machine shop, toolroom and maintenance customers.
The accessory types we stock
- Drill chuck arbors and taper adapters — Morse taper to Jacobs taper, Morse taper to DIN taper, Morse taper to threaded shank, round/parallel shank to Jacobs taper, R8 (Bridgeport-style) to Jacobs taper, R8 to DIN taper, and NT(ISO) to Jacobs taper across a range of spindle sizes and threads, in both imperial and metric
- Lathe live centres — dual-bearing and triple-bearing hardened-point centres, a 7-interchangeable-tip centre, and a pipe live centre
- Fly cutter holders — single holders plus multi-size sets for facing work on the mill
- Annular cutter arbors — MT2 and MT3 arbors with coolant or lube rings, adapting Weldon-shank annular cutters to a Morse-taper spindle, plus cutter arbor extensions
- Tapmatic tapping-head hardware — MT and BT mounting arbors, pull studs, quill clamps and stop arms for servicing a Tapmatic self-reversing tapping head
- Automatic centre punch — spring-loaded punch for fast, consistent centre-marking without a hammer
Drill chuck arbors and taper adapters — matching machine to chuck
A drill chuck (or other tooling) is built around one specific taper or shank — Jacobs (JT), Morse (MT), DIN, or a straight/parallel shank. Your machine's spindle or tailstock is built around a different taper again — Morse on most lathe tailstocks and drill presses, R8 on a Bridgeport-style mill, NT/ISO on a larger machining centre. An arbor bridges the two, and getting both ends right — the machine-side taper and the chuck-side taper or thread — is what makes it seat properly instead of running out. AIMS Industrial stocks arbors covering Morse-Jacobs, Morse-DIN, R8-Jacobs, R8-DIN and NT(ISO)-Jacobs combinations, in both imperial and metric.
Lathe live centres — supporting the workpiece at the tailstock
A live centre supports the free end of a workpiece in the lathe tailstock on its own bearings, so the centre point rotates with the workpiece instead of rubbing against it like a dead centre — less heat, less wear, and higher turning speeds. AIMS Industrial stocks dual-bearing and triple-bearing hardened-point centres for heavier turning loads, a 7-interchangeable-tip centre for switching point styles without swapping the whole centre, and a pipe live centre for tube and pipe work.
Annular cutter arbors — adapting Weldon-shank cutters to a Morse taper
Annular (core) cutters used with magnetic drills run a Weldon shank. Our MT2 and MT3 arbors, with a built-in coolant or lube ring, adapt that Weldon shank to a Morse-taper spindle so the cutter can be run in machines built around Morse taper rather than a dedicated mag-drill chuck. See our magnetic drills range for the cutters and drills themselves.
Tapmatic tapping-head hardware
Sutton Tools' Tapmatic self-reversing tapping heads rely on a handful of wear parts and mounting hardware — MT and BT arbors that fit the head to the spindle, plus pull studs, quill clamps and stop arms that set the reversing point. AIMS Industrial stocks the individual Tapmatic parts, so a head can be serviced or re-mounted without replacing the whole unit. See our tapping heads range for the heads themselves.
Care and fitting
Clean both mating tapers before fitting an arbor or adapter — chips or dirt in the taper bore stop it seating fully and cause runout, poor surface finish, or a chuck that slips under load. Seat the arbor firmly and check for wobble before use; a taper that isn't fully seated is often more obvious once the machine is running than by hand. Inspect live centre points and bearings for wear or roughness, and keep annular cutter arbor coolant/lube rings clear so cutting fluid actually reaches the cutter tip.
Brands stocked at AIMS
Maxigear supplies the bulk of our range — drill chuck arbors and taper adapters, lathe live centres, and fly cutter holders. Llambrich and Shin-Yain round out the drill chuck arbor range with additional taper and size combinations. Sutton Tools supplies the Tapmatic-branded tapping-head hardware. MAXBOR and Euroboor supply the annular cutter arbors and cutter arbor extensions, and Trax supplies the automatic centre punch.
Companion ranges at AIMS
Tool holder accessories sit alongside our broader tool holder and machining range — see drill chucks for the chucks these arbors fit, indexable turning tool holders for carbide-insert lathe tool holders, milling inserts, and thread turning tool holders for the related products.
Need help matching an arbor or adapter to a specific machine or tapping head? contact our team — we'll match by spindle taper, chuck, and tooling system.
People Also Ask — Tool Holder Accessories
Q: What's the difference between a drill chuck arbor and a taper adapter?
They do the same job — bridging one taper or shank to another so a chuck or tool built for one system can be fitted to a different machine spindle or tailstock. "Arbor" is the term generally used when the far end is built specifically to carry a drill chuck; "adapter" covers the broader family, including taper-to-taper and taper-to-thread pieces.
Q: How do I know which taper my machine spindle uses?
Morse taper (MT0-MT6) is common on lathe tailstocks and smaller drill presses; R8 is the standard on Bridgeport-style manual mills; NT/ISO tapers turn up on larger machining centres; BT tapers appear on some CNC spindles. Check the machine's manual, or measure the taper against a reference chart if it's not marked — fitting the wrong taper won't seat properly no matter how hard it's tightened.
Q: What's a live centre, and why not just use a dead centre?
A live centre rotates with the workpiece on its own bearings, rather than staying still and rubbing against the workpiece like a dead centre does. That means less friction-generated heat, less wear on the centre point, and the ability to run higher turning speeds without the centre overheating.
Q: What do the coolant/lube rings on the annular cutter arbors do?
They feed cutting fluid directly to the cutter tip during the cut. Annular cutters remove a ring of material in one pass rather than reducing the whole hole to chips, so they generate significant heat at the cutting edge — the coolant/lube ring keeps the cutter and pilot pin cool and extends cutter life.
Q: Can I fit a Tapmatic tapping head to any machine, or does it need specific hardware?
It needs the right mounting arbor (MT or BT, matched to the machine's spindle taper) plus the correct pull stud and stop arm setup for that head — that's the hardware this range covers. Fitting the wrong arbor, or skipping the stop arm setup, is a common cause of a tapping head that doesn't reverse cleanly.