CRC Trefolex CDT Cutting Oil 300g

CRC Trefolex CDT Cutting Oil is a cutting, drilling and thread cutting lubricant for use on all types of metal, supplied as a 300g aerosol (CRC product number 3063). CRC describes it as extreme pressure resistant, to increase tool life and improve cutting, with a viscosity modifier that gives extra cling so it can be used at any angle.

CRC lists it for critical machining in Machinability Group 1 (except operations such as deep drilling where a low viscosity oil is required) and for less critical operations in Machinability Group 2. The aerosol is classified as extremely flammable; the hazard details are below.

Where this product is used

• Cutting, drilling and thread cutting on all types of metal
• Critical machining in Machinability Group 1, except operations such as deep drilling where a low viscosity oil is required
• Less critical operations in Machinability Group 2
• Spot lubrication in hard to reach areas, using the extension tube

Features

• Extreme pressure resistant, to increase tool life and improve cutting (CRC)
• Viscosity modifier gives extra cling, so it can be used at any angle (CRC)
• CRC states the formula is safe on soft metals such as brass, copper and aluminium
• Leaves an anti-corrosive residue (CRC data sheet)
• Non-drying film (CRC data sheet)
• Extension tube use for hard to reach areas and spot lubrication (CRC directions)

Key specifications

Selecting the right option

For hand tool work with taps and dies, hacksaws and reamers at low speed, CRC lists its paste instead: CRC Trefolex Cutting Paste.

Using it

CRC's directions: read all directions and warnings before using. Shake the can well before using. Coat the area, ensuring total coverage, to give maximum lubrication.

Use the extension tube in hard to reach areas and for spot lubrication.

Storage and handling

Do not puncture, incinerate or store above 50°C. Store in a cool, dry, well ventilated area below 50°C.

Limits and safety

Classified as hazardous under Safe Work Australia criteria. Signal word Danger. H222: extremely flammable aerosol. H229: pressurised container, may burst if heated. Transport: UN 1950, AEROSOLS, Class 2.1. The safety data sheet gives a flash point below 23°C for the aerosol with propellant; the higher flash points on CRC's data sheet are for the oil without propellant. Not classified as a health or environmental hazard. CRC's data sheet excludes operations such as deep drilling where a low viscosity oil is required. CRC's data sheet also says aerosol cans will conduct electricity, so keep them away from live electrical sources such as battery terminals, solenoids and electrical panels. Read the safety data sheet before use.

Frequently asked questions

Is CRC Trefolex CDT Cutting Oil safe on brass, copper and aluminium?

CRC states the formula is safe on soft metals such as brass, copper and aluminium.

Is CRC Trefolex CDT Cutting Oil a flammable aerosol?

Yes. The safety data sheet classifies it as Aerosols - Flammable Category 1 (H222 extremely flammable aerosol, H229 pressurised container may burst if heated). Signal word Danger, UN 1950 Class 2.1.

What is the flash point of CRC Trefolex CDT Cutting Oil?

The safety data sheet gives below 23°C for the aerosol with propellant. CRC's data sheet gives above 150°C TOC for the aerosol oil without propellant, which is not the figure for the can.

What type of film does it leave?

CRC's data sheet lists the film as non-drying and says it leaves an anti-corrosive residue.

How do I apply CRC Trefolex CDT Cutting Oil?

Shake the can well, coat the area ensuring total coverage, and use the extension tube in hard to reach areas and for spot lubrication.

What pack size is it?

A 300g aerosol, CRC product number 3063.

Related products

See also: CRC Trefolex Cutting Paste, CRC Trefolex HD Cutting Fluid 500ml.